startrite_bandsaw
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
startrite_bandsaw [2019-05-20 19:59] – [Speeds] adding cooling recommendations vzickus | startrite_bandsaw [2022-06-18 21:18] (current) – [Log] New blade mike | ||
---|---|---|---|
Line 10: | Line 10: | ||
* Drive belt: 50" external / 48" internal A-section V-belt | * Drive belt: 50" external / 48" internal A-section V-belt | ||
+ | Laser cuttable design for the acrylic piece that goes in the centre of the table, 8-9mm thick: {{ : | ||
===== TODO ===== | ===== TODO ===== | ||
* Install dust collection | * Install dust collection | ||
Line 24: | Line 25: | ||
^ Material ^ Speed (feet/min) (thickness < 0.5") ^ Speed (feet/min) (thickness > 0.5") ^ | ^ Material ^ Speed (feet/min) (thickness < 0.5") ^ Speed (feet/min) (thickness > 0.5") ^ | ||
| Aluminium * | 1000 | 700 | | | Aluminium * | 1000 | 700 | | ||
- | | Brass - Cast | 320 | 18[Bandsawing practice] 0 | | + | | Brass - Cast | 320 | 180 | |
| Brass - Soft | 1800 | 1000 | | | Brass - Soft | 1800 | 1000 | | ||
| Cardboard | 3200 | 3200 | | | Cardboard | 3200 | 3200 | | ||
Line 39: | Line 40: | ||
* * - cooling recommended for perspex in the manual. | * * - cooling recommended for perspex in the manual. | ||
===== Saw blade width and minimum sawing radius ===== | ===== Saw blade width and minimum sawing radius ===== | ||
+ | //Table copied from the manual.// | ||
+ | |||
This is only a guide. Always err on larger radius side. Use relief cuts, and drill relief holes where necessary. | This is only a guide. Always err on larger radius side. Use relief cuts, and drill relief holes where necessary. | ||
| Saw blade width | 1/8" | 3/16" | 1/4" | 3/8" | 1/ | | Saw blade width | 1/8" | 3/16" | 1/4" | 3/8" | 1/ | ||
Line 102: | Line 105: | ||
* Blade speed too fast, and/or blade pitch too coarse. | * Blade speed too fast, and/or blade pitch too coarse. | ||
* Insufficient blade tension. | * Insufficient blade tension. | ||
+ | |||
===== Trainers & Maintainers ===== | ===== Trainers & Maintainers ===== | ||
Line 107: | Line 111: | ||
* Cameron Sharp (cazagen) | * Cameron Sharp (cazagen) | ||
- | * Alfie Pates (alfie) | ||
* Mike Walters (miek) | * Mike Walters (miek) | ||
Line 113: | Line 116: | ||
* Cameron Sharp (cazagen) | * Cameron Sharp (cazagen) | ||
* Mike Walters (miek) | * Mike Walters (miek) | ||
+ | ===== Log ===== | ||
+ | |||
+ | //Started 09/06/2019 - maintenance prior to this may not be logged. // | ||
+ | |||
+ | * **01/ | ||
+ | * **09/ | ||
+ | * **07/ | ||
+ | * **18/ |
startrite_bandsaw.1558382379.txt.gz · Last modified: 2019-05-20 19:59 by vzickus