Differences

This shows you the differences between two versions of the page.

--- purchases [2018-08-13 19:36] – [Small Stuff] tim
+++ purchases [2019-05-20 12:59] – tim
@@ Line 1: / Line 1: @@
 ====== Purchases ======
+===== Pending Deliveries =====
+  * Relay module for tool lockers
+  * I2C GPIO expanders for tool lockers
+  * Inflatables pump
+  * SSD
+  * SSD 3.5" adapter
+  * 1N4007 (M7) diodes for multimeter repair
 ===== Small Stuff =====
@@ Line 9: / Line 18: @@
 <file>
 code,quantity,description <- quick-paste format
-PL0919287,2,1m 6-way ext
+HE32378,1,Hazard tape
-PL0919387,2,2m 6-way ext
+FF02832,10,Multimeter fuses
-SA01621,1,Kim Wipes (lint-free dry wipes)
+long spirit level
-AV25542,1,gnd loop isolator
+</file>
+Farnell:
+<file>
+code,quantity,description <- quick-paste format
 </file>
 Amazon:
   *
 eBay:
-  * Breadboard jumper wires (all types)
+  * 0603 SMT resistors/caps
+  * I2C LCD adapter (re-stock for Tim)
+RS:
+  * Replacement Metcal soldering tip?
 IKEA:
   *
+Screwfix:
+  *
+Other:
+  * black hot glue
+    * will require another glue gun to avoid just having grey glue.
+    * is there a use case to justify this?
+  * null modem / serial breakouts
+  * layout paper (big masking tape)
 ===== Small Tools =====
 ^ Tool ^ Cost ^
-| Wera Kraftform Micro TORX screwdriver set | [[https://www.amazon.co.uk/dp/B0001P18PU|£23]] |
+| Wago Terminal | [[https://cpc.farnell.com/wago/222-413/terminal-block-w-lever-3cond-4mm/dp/CN12062|£0.34 for one CPC]] |
-| <del>Wera Kraftform screwdrivers (2-slot, 2-PH, 2-PZ) for G1</del> | <del>[[https://www.amazon.co.uk/Wera-Kraftform-300-Screwdriver-Piece/dp/B000297UEI|£18]]</del> |
-| Wera Kraftform nutdriver set | [[https://www.amazon.co.uk/Wera-05029510001-395-Nutdriver-piece/dp/B00154Y0MY|£30]] |
 | VDE tools (screwdrivers, pliers, cutters, voltage tester) | |
 | Combination spanners, replacement/spares | |
-| Good countersink bits | [[https://www.screwfix.com/p/erbauer-countersink-12-x-50mm/8380v|Screwfix £2.69]] times 5? |
 | Hole reamer | [[http://amzn.eu/cmG6rHp|£20]] |
-| Fine tip for Metcal soldering iron (e.g. SSC-722A) | |
-| <del>Vernier calipers</del> | <del>[[http://cpc.farnell.com/hilka-tools/76915000/vernier-calipers-150mm/dp/TL17203|CPC £12]]</del> - sucked. don't buy again.|
+===== Storage =====
-| Metric tap set | |
+Raaco louvre-mounted bins
 ===== Health and Safety =====
@@ Line 48: / Line 78: @@
 | Chemical storage cabinet | £150-250 |
 | RCD sockets for electronics area (11 twin sockets) | £156 |
+| Additional good-quality ear defenders | £13 each |
+| Workshop Aprons, decent quality waxed canvas - best 2 of them| [[https://www.amazon.co.uk/dp/B071CQGGCR/ref=cm_sw_r_cp_apa_i_uvomCb6VNDQDN|£16.99]] |
 ===== Makita 18V Cordless System =====
@@ Line 71: / Line 102: @@
   * <del>Better bandsaw, probably Startrite</del>
   * Planer-thicknesser-jointer
-===== Oscilloscope =====
-  * Rigol DS1054Z - https://roundup.ehlab.uk/issues/issue10
 ===== A new floor for G1 =====
 The vinyl flooring in G1 is rapidly deteriorating. Literally anything would be an improvement.
+Floor area 9.1x4.2m = 38.22m2.
 ===== Hot Water for G1 =====
@@ Line 97: / Line 126: @@
 ===== Amateur Radio =====
-[may be purchased via pledge]
+  * Antenna tuner. e.g. LDG Z-11 Pro II
-  * Radio: Yaesu FT-857D - used £400-500
-  * 2m/70cm vertical base antenna
-  * antenna tuner
 ===== Entertainment =====
   * [[https://www.hifiberry.com/shop/bundles/dac-bundle/|HiFiBerry DAC]] for the Pi that plays music in G1. It's currently using a USB DAC that's meant to be on the table. Pi's inbuilt output is actually a GPIO doing PWM and sounds like ass, hence needing a proper DAC.