g14_setup
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
g14_setup [2019-07-29 17:19] – [Tasks] mike | g14_setup [2022-05-31 12:54] (current) – removed MirZa | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== G14 Setup ====== | ||
- | |||
- | ===== Tasks ===== | ||
- | |||
- | These tasks can be started now: | ||
- | |||
- | * Order/ | ||
- | * Run 4 cat5 cables from G11 rack to G14 roof space | ||
- | * Install UniFi access point | ||
- | * < | ||
- | * Fit benches | ||
- | * < | ||
- | * Attach wooden battens to the wall to support the back of the worktops | ||
- | * < | ||
- | * Sand & oil the worktops | ||
- | * < | ||
- | * < | ||
- | * Coat 3 | ||
- | * Attach legs and fit the worktops, attaching them to the battens with L brackets - slotted so they can move up and down a bit(?) | ||
- | |||
- | |||
- | ===== Access control ===== | ||
- | |||
- | < | ||
- | |||
- | Done! | ||
- | |||
- | ===== Floor ===== | ||
- | |||
- | The floor has damage that will need to be filled. Then it can be painted or covered with vinyl (this is a more practical task than for G1 as the space is small and already empty). | ||
- | |||
- | ESD flooring has been proposed but is likely to be expensive. We have a roll of ESD flooring but it is soft (anti-fatigue, | ||
- | |||
- | The sink cabinet can support its own (empty) weight if the legs are raised. | ||
- | |||
- | ===== Networking ===== | ||
- | |||
- | Cables will be run from the server rack in G11 (2-4 would be appropriate). A UniFi access point will be installed (this is in stock). | ||
- | |||
- | ===== Benches and storage ===== | ||
- | |||
- | Proposed: 60-80cm benches against the long walls of the room. No bench on the short ends (because corners are too restrictive). Worktops will be installed at ~75cm height for seated use. | ||
- | |||
- | Use the short end (away from the door) for component drawers and pick bins. Shelving over the benches (some mix of general storage and ready-to-use equipment). | ||
- | |||
- | ==== Cheap IKEA ==== | ||
- | |||
- | [[https:// | ||
- | |||
- | Cheap, but not very durable. | ||
- | |||
- | ==== Solid Wood ==== | ||
- | |||
- | [[https:// | ||
- | |||
- | ==== Storage ==== | ||
- | |||
- | On the short (far) wall: | ||
- | |||
- | * pick bins below the conduit | ||
- | * component drawers above the conduit (up to 7 units can fit across the width of the wall). | ||
- | * normal shelves above the component drawers | ||
- | |||
- | Above the conduit over the workbenches we will fit twinslot shelf rails: | ||
- | |||
- | * 15-30cm shelves above the conduit for oscilloscopes, | ||
- | * louvre panels above for other tools and easy-access pick bins. | ||
- | * normal shelves above the panels. | ||
- | |||
- | [[http:// | ||
- | [[http:// | ||
- | Two Raaco panels with bins - £72-£83. | ||
g14_setup.1564420772.txt.gz · Last modified: 2019-07-29 17:19 by mike